2400 MHz UPconverter BU500

Input freq.: 28.........1300 MHz Input Power: 200mW max. * SMA female

Output freq.: 2365.........2500 MHz Output power: up to 2 Watt * SMA female

LO clock: 10 MHz Stability: 2ppm ( -20°....+60°C ) Ext. clock 10 MHz input SMA port on board

Local Oscillator frequency freely programmable by the customer in 1kHz steps ( 1050.....2700MHz )

Vcc: 10.....14 Volt Icc: max. 1.5 Amper

* Output power 2W for CW SSB FM mode , DATV mode use please only to 300mW output !!

Output power is adjustable from 0 up to 2 Watt
When ordering , specify which modulation types you want to use ( SSB or DATV or both ).
28MHz and 50MHz signals can only be used with good 2.4 GHz Bandpass filters.

Die neue Version vom bereits bekannten Allmode UPconverter BU500 1.7W ist bei HiDes bereit zum Liefern.... www.hides.com.tw

Also available in Europa .....ask 9a6rzn@gmail.com

New version of already known Allmode UPconverter BU500 1.7W is ready for deliver at HiDes. Current PCB version is nr. DB-v08 For further BU500 information and experiences email me: 9a6rzn@gmail.com

Newest version.....

https://www.youtube.com/watch?v=ks4BFiLEbVY

You will receive a ready to use device , already installed in the housing on the heat sink and tested !

Manufacturer Published Date from the Ebay offer :
Excellent 13cm UP converter for SSB CW FM FM-ATV DVB
Good for QO-100 , first geostationary satellite with HamRadio transponder
BU500 specification:
RF-in : 100~1300Mhz
Local Oscillator: Default:1968MHz for 70cm IF signal
–1050MHz to 2700MHz
( configurable by customer in 1Khz step )
Local Oscillator TK stability 2.5ppm( -30°…+75°C)
     ( for even more stability: external 10MHz input is available )
RF-output: 2365~2500MHz
Conversion Gain > 34dB
Output power: 1700mW ( SSB CW FM ATV FMATV )
200mW ( DVB-T DVB-S )
DC power adaptor: 12V 1A ( 9V……13.8V )
For the Rx <--->Tx switch, please use IF signal !!! PTT on your microphone
-15dBm and +20dBm IF version ( please check your version before using it )

Version 1 for multi-mode SSB CW FM ATV D-ATV   .....with input around -15dBm
Version 2 for SSB CW FM ...with input around + 20dBm   ( attenuator on PCB included )

Please note the version you would like to buy

Product video: https://www.youtube.com/watch?v=ddjgcbQkTGc

BU500 order via Ebay: https://www.ebay.com/itm/225607477696?hash=item348740e9c0:g:MTwAAOSwOPldZMk9

http://www.hides.com.tw/product_eoa100_collapse_eng.html

or directly via HiDes website: www.hides.com.tw calvin@hides.com.tw

BU500 works well from 28MHz, but in such an interconnection a good bandpass filter is also needed between BU500 and power amplifier. This applies to 28MHz and 50MHz IF use , that's why HiDes decided to write 100...1300MHz in data specification.

v.08 --> What improvements have been made in the circuit diagram and PCB compared to old versions V06 :

1. Better cooling to provide permanently more output power, up to 2W - larger milled heat sinks

2. the new 1.7W version has built-in switch for externly GPS or internal TCXO Clock

3. More output power by removing unsuitable Bandpass filters

4. An attenuator installed on the IF port to allow more input power - now up to 200mW
To have the sensitive version ( for Adalm Pluto - without this attenuator ) with -15dBm input , you have to order V01

5. Reverse Vcc polarity protection

6. Operating voltage has been increased ( 9....16V ) , Switching power supply replaced

7. Nicer output HF Spectrum - better LO Freq. suppression

Output Port - Testdata

Measured by OE7DBH , Graphic by ON6JM

Typical test report - data sheet of a delivered BU500 UPconverter

Mirror frequency suppression for 2m IF Signals....

Mirror frequency suppression for 70cm IF Signals...

The higher the BU500 IF signal frequency, the better the test data and no Bandpass Filter is necessary !!

Excellently suitable for IC-9700 in satellite working mode

( IC-9700 TX in 23cm band and IC-9700 RX in 70cm band with 70cm output LNB )

( QO-100 LNB with Signal output in 70cm band available from: 9a6rzn@gmail.com )

-------------------------------- Software and User Manual -----------------------------------

www.hides.com.tw -----> downloads -----> BU500 ----> dropbox upper right "download" ---> "direct download"
Please search your file in download Folder -----> unzip zip file -----> print pdf user Manual and please read !!

Wenn Sie den BU500 mit einen 70cm Signal betreiben möchten dann können sie ihn so verwenden wie ausgeliefert worden ist ! ( achten auf beigefügten Zettel ) If you want to operate the BU500 with a 70cm signal then you can use it as delivered !
Wenn Sie aber eine andere Local Oscilator Frequenz benötigen, dann instalieren sie bitte den Driver in ihren Computer: "Windows_Driver_v16... " ( After purchasing the BU500 you will receive a download link )

https://www.dropbox.com/sh/nvempmxvo3dxa4r/AABjF8flQFzrFhkcX703rwx5a?dl=0

....However, if you need a different local oscillator frequency, please install the driver into your computer
-------------------------- Reprogramming Local Oscilator for other IF frequency. ------------------------------------------
Ablesen welche LO Frequenz programmiert ist.... Reading which LO frequency is programmed…