2.4 GHz MMDS Down converter

 


Hier umbau eines PLL gelocktes 13cm down converter, na ja umbau ist übertrieben...einfach Dipol mit 
N Buchse getauscht.
Habe 3 Stück geliefert bekommen und davon ist einer zuviel, falls jemand einen in original zustand 
brauchen kann ? , kann ihn bei mir bekommen.
Oscilator ist einfach Schleife PLL gelockt auf 1998MHz und gut für DVB-T , DVB-S , FMATV und FM empfang.
Zb. FM 2430MHz - 1998MHz = 432MHz Receiver 
........... oder DATV    2400MHz - 1998MHz   =   402MHz DVB-T Receiver




Already rebuilt downconverter from the last picture with N connector on the input, in stock for sale for 80 euros.        9a6rzn@gmail.com










Kommentare

Kommentar veröffentlichen

Beliebte Posts aus diesem Blog

2400 MHz UPconverter BU500

Bild
  Input freq.:   28.........1300 MHz                                    Input Power:    200mW max.  *         SMA female Output freq.:   2365.........2500 MHz                             Output power:    up to 2 Watt  *     SMA female LO clock:    10 MHz         Stability:  2ppm ( -20°....+60°C )         Ext. clock 10 MHz input SMA port on board  Local Oscillator frequency freely programmable by the customer in 1kHz steps ( 1050.....2700MHz ) Vcc:     10.....14 Volt              Icc:   max. 1.5 Amper *   Output power 2W  for CW SSB FM mode ,   DATV mode use please only to 300mW output !!     Output power is adjustable from 0 up to 2 Watt      When ordering , specify which modulation types you want to use   (  SSB  or  DATV  or both ).      28MHz and 50MHz signals can only be used with good 2.4 GHz Bandpass filters . Die neue Version vom bereits bekannten Allmode UPconverter    BU500 1.7W  ist bei HiDes bereit zum Liefern....  www.hides.com.tw New version of already known Allmode
Mehr anzeigen

2.4 GHz 30W TX UPlink for QO-100 with IF 50....1300MHz

Bild
  For QO-100 transponder or other use ……2400MHz UPconverter-Transmitter for SSB Signals with  IF  between 50MHz and 1300MHz Just like in the pictures ready for use with 144,500 MHz input signal ( 20mW maximal ).  BU500 is freely programmable by customer for all IF signals between 50MHz and 1300MHz,  bandpass filter is already adjusted for all the signals and modulations mode ( DATV - SSB - CW ) . BU500 Upconverter  ………with GPSDO 10MHZ input port on board !! PA output power is 30W and antenna port is secured with an isolator against poor antenna VSWR  , SMA out. Band Pass Filter Result……… Output power test with 144,500MHz IF input Signal....
Mehr anzeigen

10GHZ input - Down Converter 3LNC70 - 432MHz output

Bild
  10 GHz input      and    70cm band Output  , with option ext. GPS input It is my pleasure to present a new product for 10GHZ amateur radio operators from  www.hides.com.tw Low-noise selective 10GHZ LNC in coaxial form (  for various applications …  direct 10GHz FM-SSB QSO , DVB-T QSO , QO100 SSB QSO , QO-100 DVBt or DVBs QSO  ) and power supply either via coax or external. https://www.youtube.com/watch?v=Sg19EgpPBJQ   Size: 70 x 47 x 21mm Input-Output-Ext LO connectors: 50ohm , SMA female Noise figure: 1,2~1,3dB Recommended RF input range: 9,8GHz.......10,7GHz Recommended IF output range: 300.........2000 MHz Recommended Vcc voltage: 8V.....14V Recommended Freq. range for Ext. LOsync input: 25,4......29,8MHz  ( with the internal quartz switched off ) LNC consumption in original condition is approx. 150mA , power supply options here...... Technicians who want to install a TCXO with more stability themselves, there is enough space on the underside of the PCB. HiDes provides the 3.3V po
Mehr anzeigen